Fill in the gap with the necessary information. — КиберПедия 

Состав сооружений: решетки и песколовки: Решетки – это первое устройство в схеме очистных сооружений. Они представляют...

Опора деревянной одностоечной и способы укрепление угловых опор: Опоры ВЛ - конструкции, предназначен­ные для поддерживания проводов на необходимой высоте над землей, водой...

Fill in the gap with the necessary information.

2017-09-10 254
Fill in the gap with the necessary information. 0.00 из 5.00 0 оценок
Заказать работу

1. Gasoline internal-combustion engines power most automobiles, but some engines use diesel fuel, ____, natural gas, ____, or fuels derived from methanol (wood alcohol) and ethanol (grain alcohol).

2. Turning the ignition key operates a switch that sends electricity from a ______to a starter motor.

3. The fuel mixture explodes, or combusts, creating _________that push the pistons down the cylinders and cause the crankshaft to rotate.

4. The lower part of the engine, called the________, houses the cylinders, pistons, and crankshaft.

5. The upper part of the engine, the ______, bolted to the top of the block, seals the tops of the cylinders.

6. Fuel vapor enters and exhaust gases leave the combustion chamber through _____in the cylinder head controlled by valves.

7. A_____ or chain links the camshaft to the crankshaft.

8. Diesel engines, common in large trucks or buses, are similar to gasoline internal-combustion engines, but they have a different ____________.

9. Some cars have _______ engines, also known as Wankel engines, which have one or more elliptical chambers in which triangular-shaped rotors, instead of pistons, rotate.

10. All new cars produced today are equipped with _____________instead of carburetors.

 

Questions for discussion.

1. Disclose the work of gasoline internal-combustion engines.

2. What are the basic components of an internal-combustion engine?

3. What is the difference between in-line designs or V designs blocks in most internal-combustion engines?

4. Explain the work of the carburetor.

5. What are the advantages of the fuel injection system in comparison with the carburetor?

6. What pluses does the air-compressing equipment bring to the automobile?

7. Disclose the work of the automobile exhaust system.

8. What equipment of the automobile prevents from cast iron melting inside an engine?

9. What was the coolant in early engines? And how is it called today?

10. For what purpose does the automobile have the second smaller radiator?

Unit III

Drivetrain

Vocabulary to be remembered.

Make your own sentences using the word combinations with the word gear.

Gear а) шестерня

gears grind — шестеренки стачиваются; gears jam — шестеренки заедают; gears lock — шестеренки заклинивает; gears mesh — шестеренки крутятся;

б) передаточный механизм, привод

a worm gear — червячный привод; in gear — включенный, сцепленный, действующий;

out of gear — не включенный, недействующий, неработающий; to throw out of gear — выключить передачу; to get into gear — включить передачу; включиться в работу

в) зубчатая передача

to change gears, to shift gears — переключать передачу; to go into 1st, 2nd, etc. gear — переключаться на 1-ю, 2-ю и т. д. cкорость; bottom gear, low gear — нижняя, первая передача; high gear, top gear — верхняя передача; reverse gear — задняя передача.

gearbox 1) коробка передач, коробка скоростей; тж. коробка подач

2) редуктор

crankshaft -коленчатый вал

drivetrain – ходовая часть

driveshaft – карданный вал

differential gears - дифференциальная передача

torque - вращающий момент

rear axle – задняя ось

continuously variable - 1) непрерывная переменная 2) с бесступенчатым регулированием

steering column - рулевая колонка

shift lever - рычаг переключения передач или скоростей

clutch – сцепление

input shaft – ведущий вал

circular plate -ведомый диск

clutch disk – нажимной диск

clutch fork – вилка выключения сцепления

throwout bearing – рычаг выключения передачи

 

 

Read the text paying attention to the vocabulary.

The rotational force of the engine’s crankshaft turns other shafts and gears that eventually cause the drive wheels to rotate. The various components that link the crankshaft to the drive wheels make up the drivetrain. The major parts of the drivetrain include the transmission, one or more driveshafts, differential gears, and axles.

A. Transmission

The transmission, also known as the gearbox, transfers power from the engine to the driveshaft. As the engine’s crankshaft rotates, combinations of transmission gears pass the energy along to a driveshaft. The driveshaft causes axles to rotate and turn the wheels. By using gears of different sizes, a transmission

alters the rotational speed and torque of the engine passed along to the driveshaft. Higher gears permit the car to travel faster, while low gears provide more power for starting a car from a standstill and for climbing hills.

The transmission usually is located just behind the engine, although some automobiles were designed with a transmission mounted on the rear axle. There are three basic transmission types: manual, automatic, and continuously variable.

A manual transmission has a gearbox from which the driver selects specific gears depending on road speed and engine load. Gears are selected with a shift lever located on the floor next to the driver or on the steering column. The driver presses on the clutch to disengage the transmission from the engine to permit a change of gears. The clutch disk attaches to the transmission’s input shaft. It presses against a circular plate attached to the engine’s flywheel. When the driver presses down on the clutch pedal to shift gears, a mechanical lever called a clutch fork and a device called a throwout bearing separate the two disks.

 

Releasing the clutch pedal presses the two disks together, transferring torque from the engine to the transmission.

An automatic transmission selects gears itself according to road conditions and the amount of load on the engine. Instead of a manual clutch, automatic transmissions use a hydraulic torque converter to transfer engine power to the transmission.

Instead of making distinct changes from one gear to the next, a continuously variable transmission uses belts and pulleys to smoothly slide the gear ratio up

 

or down. Continuously variable transmissions appeared on machinery during the 19th century and on a few small-engine automobiles as early as 1900. The

transmission keeps the engine running at its most efficient speed by more precisely matching the gear ratio to the situation. Commercial applications have been limited to small engines.

 


Поделиться с друзьями:

Состав сооружений: решетки и песколовки: Решетки – это первое устройство в схеме очистных сооружений. Они представляют...

История развития хранилищ для нефти: Первые склады нефти появились в XVII веке. Они представляли собой землянные ямы-амбара глубиной 4…5 м...

Автоматическое растормаживание колес: Тормозные устройства колес предназначены для уменьше­ния длины пробега и улучшения маневрирования ВС при...

Биохимия спиртового брожения: Основу технологии получения пива составляет спиртовое брожение, - при котором сахар превращается...



© cyberpedia.su 2017-2024 - Не является автором материалов. Исключительное право сохранено за автором текста.
Если вы не хотите, чтобы данный материал был у нас на сайте, перейдите по ссылке: Нарушение авторских прав. Мы поможем в написании вашей работы!

0.01 с.