Operational procedures when using the device

1. ZENWAVES device has an aluminum-plastic body with a mirror insert on the front panel and has:

- two LEDs (1) on the front panel

- operation mode selection button (2) on the rear panel

- BL mode activation indicator (3) on the rear panel

- power cord (4) with USB connector to connect to any network adapter of 5V B

 

2. Connect the device to a power source, herein the 1st mode will turn on.

3. Each pressing of the operation mode selection button on the rear panel of the device increases the operation mode number1-2-3-4-5, and so circle wise.

4. When activating the algorithm ‘White-colorful’ (modes 1 and 2) the LEDs on the front panel shine with white color for a second. Then the analysis process begins.

5. When activating the algorithm ‘Rainbow’ (modes 3 and 4), the front panel LEDs change colors around the whole color circle for two seconds. Then the analysis process begins.

6. When activating the BL technology (Modes 2, 4, and 5) the corresponding indicator the rear panel lights on.

7. In mode 5, when only the BL technology is active, the front panel LEDs do not illuminate, only the corresponding indicator on the rear panel illuminates.

8. To turn off the device, disconnect it from the power supply.

 

Directions for security measures

1. The device is made in accordance with the requirements of the product with the internal power source.

2. No direct ingress of water in the slots and the device connector is allowed.

1. In case of any faults during operation switch it off immediately. Do not use the device with a clearly visible impairment of its appearance (broken case).
2. Do not place the device near open flames.
3. Do not leave the device for a long time in direct sunlight.
4. Keep out of reach of children.
5. Do not use the device in bathrooms and wet rooms.
6. Using the device for children is permitted only under adult supervision.
7. Do not place the device in a microwave oven.
8. Do not separate the device apart.
9. Not put the device in water.

Technical specifications

Dimensions no more than 72 x 150 x 24 mm

Weight no more than 290 g

Signal parameters:

The intensity of electric component of the field no more than 10 V / m

The intensity of the magnetic component of the field no more than 0.1 A / m

Spectrum - noise with a comb structural streak up to 10 kHz

Comb step - 7.8 Hz

The maximum of the spectral density in the range of 200 Hz

Power supply 5 V

Current consumption no more than 300 mA

Warranty

1. The manufacturer guarantees the accordance of the device under conditions of storage, transportation and operation.

2. Warranty period - one year from the date of purchase.

3. When detecting any mechanical failure of device’s components occurred not through the fault of the user, there can be replaced both the entire device or its components, the replacement is performed at the discretion of the manufacturer.

4. The guarantee does not apply to the device with the evidence of essential mechanical and chemical damages which compromise the structural integrity of the device.

5. The warranty period is calculated from the date of purchase of the device or the date of its receipt by mail.

6. At the expiration of the warranty period the repair is carried out under a separate contract between the consumer and the manufacturer.

Свидетельство о приемке

 

Устройство «ZENWAVES» изготовлено и принято в соответствии с обязательными требованиями государственных стандартов, действующей документации и признан годным для эксплуатации.

Отметка технического контроля

МП__________________________________________

              (личная подпись)             (расшифровка подписи)

_______________________

        (дата выпуска)

Certificate of acceptance

 

The ‘ZENWAVE’ device is manufactured and accepted in accordance with the mandatory requirements of state standards and applicable documentation and was approved for exploitation.

Technical control mark

SE __________________________________________

              (Personal signature) (clarification of signature)

_______________________

        (Date of issue)

Гарантийный талон (Заполняется продавцом)

Устройство « ZENWAVES »

Продавец_________________

           Дата продажи «__»________201 г. Штамп торгового предприятия:

Заполняется при ремонте:

Выполненные работы по ремонту:

________________________________________________________________________________________________________________________________

Исполнитель__________________________________

М.П.                                 Дата «__»________201 г.

Компания БИОМЕДИС 105122, Москва, Щелковское, шоссе, 5/1

Warranty card (Filled by manufacturer)

The device "ZENWAVE "

Seller_________________

           Sale Date "__" ________ 201, The stamp of the commercial enterprise:

Filled in the repair of:

Performed repairs:

________________________________________________________________________________________________________________________________

Executor__________________________________

SE           Date "__" ________ 201 y.

Company BIOMEDIS 105122, Moscow, Schelkovskoe, highway, 5/1